Lower the tables A on both sides of the planer as shown in Fig. The top surface of extension tables should be level with the planer table. Assemble chip deflector A Fig. Make certain the two screws, one of which is shown at B are inserted upward through the two slots C in the chip deflector. Page Leveling Extension Tables A with one end extending out over the extension table as shown. Check to see if the infeed table is level with the planer table on both ends of the extension table.
If an adjustment is necessary, loosen locknut C Fig. If an adjustment to one or both knives is necessary, slightly loosen the seven locking screws, six of which are shown at C Fig.
Page Lifting Straps 3. Plane both sides of the board until you are satisfied with the thickness, making thin cuts with each pass. Page Maintenance C Fig. Replace the side cover. Lay the planer on its back and squirt oil on the feed roller bushings D Fig.
Page 14 Delta Building Trades and Home Shop Machinery Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection.
Question: Knife Lock Bar Hello , You just keep searching on line for one. Or find someone that has a planer not worth repair that they are selling or they are parting out. If you go to ytube there are nine videos by "ghostses" who takes this planer apart and it shows where the springs go. Hello jtkarst, The switch in question part number K21 is an aftermarket switch that we offer when the manufacture's part is on back order or no longer available. To answer your question it will work in your Delta planer.
Question: Delta poppajack. Hello poppajack, To remove the cutterhead pulley. You will have to remove the nut, part number Sometimes they are on the shaft pretty snug. You can tap it with a mallet to get it off the shaft. But don't loose the key that holds it on to the shaft. Good luck, -WJA.
Question: Spring For Planer Birdhouselady. Does anyone know a supplier for the springs under the planer blades for a delta planer?? Hello , You may want to try to locate a Spring Supplier in your area. Or try a hardware store, most of them have assortments of springs. They may be able to match up the Delta part number Question: Delta Type 2 Planer scottnrtn. Hello scottnrtn, Even though the manufacture is not supplying the bushings for the the gear box.
They are still supplying the complete gear box assembly. It is part number, It is a little bit more money than just the bushings though. Question: Delta Planer I bought a used Delta planer and can't locate a knife setting gauge.
They're on back order at Delta. Any ideas on how I can set the knife height without one? Hello, A company by the name of Woodstock International offers a knife setting jig sold under the name of " Mini Planer Pal ". Google that and you should be able to locate one in your area. Good luck, WJA. I need to replace the blades. I followed the directions but one screw is stuck on each blade. Can't get it to turn.
Any suggestions? Using a pointed punch and a hammer, drive the head of the bolt clockwise. Be gentle at first, using only as much force as you have to.
Periodically use the wrench. It will give up after enough time. Randy I tried to use this method but the screw is stuck fast. Any other ideas? Hello mano, There is a company the manufactures a screw extractor kit. The name of the company is Grabit. The have a three piece kit. Search for a retailer in your area that supplies them. I have a set of them at home and the work great. Improper connection of the equipment-grounding conductor can result in risk of electric shock.
The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipmentgrounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded.
Grounded, cord-connected tools intended for use on a supply circuit having a nominal rating less than volts:. This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. The tool has a grounding plug that looks like the plug illustrated in Fig. A temporary adapter, which looks like the adapter illustrated in Fig.
BB, may be used to connect this plug a 2-hole receptacle as shown in Fig. BB if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician.
The green-colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. Whenever the adapter is used, it must be held in place with a metal screw. Use proper extension cords. When using an extension cord, be sure to use one heavy enough to carry the current of the saw. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating.
DD, shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. Delta Model is a 12" mm Portable Planer with adjustable feed rate for optimum planing under load. Features include; basic machine with powerful 15 amp, volt motor, dust chute, two-knife cutterhead with an extra set of high-speed steel, double-edged reversible knives; knife-setting gage and wrench, polyurethane feed rolls and adjustable-folding table extensions.
Carefully unpack the tool and all loose items from the shipping container s. Peel protective film from the table surface. Remove and clean the protective coating from the cutterhead. Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene do not use acetone, gasoline or lacquer thinner for this purpose. After cleaning, cover the unpainted sufaces with a good quality paste wax. Welcome to ManualMachine. We have sent a verification link to to complete your registration.
Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Delta User Manual Download for 1. Refer to them 2 frequently and use them to instruct other users.
0コメント